Jkssb JE Civil syllabus 2021
Jkssb Junior Engineer Civil syllabus, recruitment and exam pattern
| Recruiting Agency | |
|---|---|
| Name of the post | Junior Engineer(Civil) |
| Department | Public Works(R&B) Department |
| Cadre of the post | UT |
| Pay Scale | Level-6(35400-112400) |
| No. of Vacancies | Total-144 OM-71, SC-12, ST-14, OSC-6, ALC/IB-6, RBA-15, PSP-6 and EWS-14 |
| Qualification prescribed | Three years Diploma in Civil Engineering from Govt. recognized Institute/Indian University Degree in Civil Engineering or AMIE section (A&B) India. |
| Criteria for selection | The selection for the post shall be made on the basis of merit obtained in written examination only. |
Jkssb JE Civil Exam Pattern :-
- Exam Will be Objective Type.
- Questions will be in the form of Multiple Choice Questions (MCQ).
- Maximum Marks for this Exam will be 120 Marks.
- Time allocated for this Exam will be of 2 hours.
- There will be a negative marking of 0.25 Marks.
Jkssb JE Civil syllabus 2021
1. Surveying:- ( 10 Marks )
Importance of surveying, principles and classifications, measurements of distance and directions, chain surveying, compass surveying, leveling, tachometry, theodolite, traversing, contouring, plane table surveying, curves.
2. Mechanics and Structural analysis:- ( 15 Marks )
Introduction, Concept of rigid body scalar and vector quantities, Laws of force, moment, friction, Centre of gravity, simple machines, torsion, Properties of material, Bending moment and shear force in statically determinate beams. Simple stress and strain relationship. Stress and strain in two dimensions, principal stresses, stress transformation. Simple bending theory, flexural and
shear stresses, unsymmetrical bending, shear Centre. Thin-walled pressure vessels, uniform torsion, buckling of column, combined and direct bending stresses. slope and deflection, Analysis of trusses.
3. RCC Structures:- ( 15 Marks )
Concrete technology, Ingredients of concrete, water cement ratio, workability properties of concrete, admixtures, special concretes, Nondestructive tests, basics of mix design. Concrete design-basic working stress and limit state design concepts, analysis of ultimate load capacity and design of members subjected to flexure, shear, compression and torsion by limit state methods. Basic elements of pre-stressed concrete, analysis of beam sections at transfer and service loads, one-way slab, two-way slab.
4. Soil Mechanics:- ( 10 Marks )
Origin of soils, properties, soil classification, three phase system, fundamental definitions, relationship and interrelationship, flow of water through soils, permeability & seepage, effective stress principle, deformation of soils, consolidation, compaction, shear strength characteristics, plate load test, SPT, Density control, Measurement of field density by core cutter and sand replacement method, soil exploration, bearing capacity and its methods.
5. Fluid Mechanics and Hydraulics:- ( 15 Marks )
Properties of fluids, hydrostatic pressure, measurement of pressure, flow measurements, flow through pipes, flow through open channels, hydraulic pumps, principle of conservation of mass, momentum, energy and corresponding equations, potential flow, applications of momentum and Bernoulli’s equation, laminar and turbulent flow, flow in pipes, pipe networks. Concept of boundary
layer and its growth. Uniform flow, critical flow and gradually varied flow in channels, specific energy concept, hydraulic jump Forces on immersed bodies, flow measurements in channels, tanks and pipes. Dimensional analysis and hydraulic modeling Kinematics of flow.
6. Irrigation Engineering:- ( 10 Marks )
Introduction, water requirement of crops, hydrological cycle, Dams, Canals, dams, canal head works and regulatory works, cross drainage works, hydraulic structures, river training works, water-logging, drainage, ground water recharge, well hydraulics.
7. Water supply and waste water Engineering:- ( 10 Marks )
Introduction, quantity of water, quality of water, water treatment, conveyance of water, laying out of pipes, building water supply, water supply fixtures and installation, plumbing, sewerage system, laying and construction of sewers, sewage characteristics, Methods of disposal, sewage treatment, building drainage, air and noise pollution.
8. Highway Engineering:- ( 10 Marks )
History of development of highway and planning, Definitions of various terms used in highway engineering., Methods of road construction, IRC classification, Highway surveys and plans Geometric design, Different types of road materials in use, Binders, Types of pavement, CBR method, sub grade preparation, WBM, WMM, Bituminous Macadam, dense bituminous macadam, special problems in hill road.
9. Railway Engineering:- ( 10 Marks )
History of Indian railways, Gauges used, permanent way its components, Types of rails, creep, welding, Rail fixtures and fastenings, Signaling, Points and Crossings, Bridge terminology, classification, components, foundations.
10. Construction planning management:- ( 15 Marks )
Network diagrams, PERT-CPM, cost optimization contracts, tenders, depreciation, valuation, organization, measurement books, cash book, functions of management, construction planning, quality control, inventory control, Estimation and costing definitions, methods of estimation and type of estimates.
COMMENTS